If your power cuts out every time a second AC comes on, or the distribution board runs hot at midday, you need an electrician in Al-Khalidiyah, Makkah who understands summer loads, not someone who flips the breaker back and leaves. Our technicians in Al-Khalidiyah run dedicated AC circuits with correctly sized breakers, upgrade old boards and rebalance loads so the summer passes without outages. We answer 24 hours a day on 0565564857, by call or WhatsApp.
Al-Khalidiyah is made up of apartment blocks, family flats and villas. Many of these flats were wired for a couple of air conditioners; over the years residents added a split unit in every room, a bigger water heater and an electric oven, and the same board now carries far more than it was designed for. We see the result in the calls: a main breaker that drops at peak time, charred cable ends inside the board, AC sockets melted by heat.
A tripping-free summer in Al-Khalidiyah
- Focus: a dedicated line and correct breaker for each AC, board upgrades and load balancing
- Send first: a clear photo inside the board, and how many ACs you run and their size
- How we test: current measured on every circuit, plus a thermal camera for hot spots
- Price: set after seeing the board or a photo of it, and agreed before work
- Payment: after all ACs are run together in front of you
- Guarantee: workmanship guarantee; the technician will explain its period
Why the power trips with the ACs on
A breaker never trips for no reason. It trips because it sees more current than it is rated for, or because heat inside the board has made it more sensitive. In Al-Khalidiyah homes three causes come up again and again, and often two of them are present at once.
Two or three ACs on one circuit
Older flats often have a single circuit feeding two or three rooms, with each room’s AC plugged into an ordinary socket on it. In winter nobody notices; on the first hot day everything runs together and the breaker starts dropping. The right fix is not a bigger breaker but a dedicated line from the board to each AC, with cable sized for the unit and the run length, and its own labelled breaker.
An old board with loose terminals
Metal expands in the heat of the day and contracts under the AC at night, and terminal screws slowly loosen. A loose terminal heats up, and heat loosens it further. You see it as blackening around a breaker or a smell of hot plastic when you open the board door. We re-torque the terminals, cut back burnt cable and replace any breaker whose body has been affected.
Unbalanced phases in villas
Some villas here have a three-phase supply, yet the internal wiring put most of the heavy loads on one phase. One phase runs hot while the others sit half empty. We measure each phase with the ACs running and move circuits until the load evens out, which on its own cures a lot of nuisance tripping.
Everything after the meter is our job inside your home. The meter, the incoming cable and any weakness in grid voltage belong to the Saudi Electricity Company, and we tell you plainly when a fault is on their side. For our full range of work, see the home electrician in Makkah page.
Overload signs and what we do about them
| Sign | What it usually means | Action |
|---|---|---|
| Main breaker trips only in the afternoon | peak load exceeds the board capacity | measure total load and redistribute, or upgrade the board |
| One room’s breaker trips when its AC starts | AC on a shared circuit or undersized breaker | dedicated AC line on its own breaker |
| AC socket hot or discoloured | a standard socket that cannot handle the current | remove it and connect via a proper isolator |
| Lamps go dim the moment a compressor kicks in | voltage drop on a long or thin cable | measure voltage and upsize the cable |
| Buzzing or smell from the board | loose terminal or damaged breaker | isolate, tighten and replace damaged parts |
Breaker dropping every afternoon?
Photograph the inside of your board and send it to 0565564857. Often we can tell from the photo whether it needs tightening or new lines.
Call 0565564857WhatsAppNew breaker or new board?
Many callers ask for “a bigger breaker”. The breaker does not carry the power; the cable behind it does, and the breaker exists to protect that cable. Put a larger breaker on a thin cable and you have switched the protection off: the cable heats inside the wall and nothing trips. So we decide by measurement:
- Just a breaker when the breaker itself is old or damaged and the cable is sound and sized for the load.
- A new line when an AC or heater shares a circuit, or the cable is thinner than the appliance needs.
- A new board when there is no space for more breakers, the base is charred, there is no earth-leakage protection, or nobody knows what each breaker feeds.
A new board does not mean breaking up the flat. In most homes here we fit it where the old one was, reconnect existing circuits, add the AC lines in neat surface trunking or concealed conduit depending on the wall, and stick a circuit chart inside the door.
A pre-summer check we recommend
- Compare the main breaker rating with the total of your ACs and heaters.
- Open the board, tighten every terminal and scan it with a thermal camera under load.
- Confirm each AC has its own line and breaker, and note any that do not.
- Measure voltage at the furthest AC while it runs.
- Test the RCD with its test button, or fit one if missing.
- Check heater and oven sockets, the next biggest loads after the ACs.
Savings you will notice: an AC on a sound line with stable voltage runs its compressor more efficiently. A moderate thermostat setting, closed doors on unused rooms and clean filters ease the load on the board and the bill together.
Other work from our Al-Khalidiyah electrician
ACs and boards are the summer story here, but the technician fixes everything else too. The complete list is on our electrician in Makkah page.
Emergency faults
repeated tripping, partial outages, burning smells and thermal short-circuit tracing.
Wiring
first-fix and finishing for flats, villas and annexes; rewiring older homes.
Lighting and fans
chandeliers, spotlights, hidden LED, outdoor lighting, ceiling and exhaust fans.
Heaters and kitchens
water heaters with isolators, thermostat and element checks, oven and hood circuits.
Pumps and roofs
water pumps, tank floats, roof and annex lighting.
Extras
CCTV, intercoms, smart switches, EV chargers, earthing and surge protection, generator changeover.
How a visit runs in Al-Khalidiyah
- Call or message 0565564857, mention Al-Khalidiyah and that the issue is ACs or the board.
- Send a photo of the open board and, if possible, the AC rating plate.
- We book a slot and send a technician the same day where we can, with a real arrival time.
- The technician measures current and voltage with the ACs running and thermal-scans the board.
- He explains what he found and gives the price; nothing starts without your yes.
- Afterwards every AC is run together in front of you to confirm nothing trips or heats up, then you pay.
What sets the price for AC lines and boards
We do not quote fixed figures before seeing the job, because electrical work varies enormously. An AC line in a flat with the board next to the bedroom is a different job from one in a villa where the cable climbs three floors, and a small flat’s board is nothing like a three-phase villa board. The price is set after the electrician sees the job, or a photo or video you send on WhatsApp, and agreed before work starts.
| Job | What sets the price |
|---|---|
| Load and tripping inspection | how many circuits need measuring and whether the board needs a thermal scan |
| Dedicated AC line with its own breaker | distance from board to AC, cable size, surface or concealed route |
| Breaker replacement | rating and type, and the state of the terminals and cable |
| New distribution board | number of circuits, single or three phase, RCD and labelling |
| Phase load balancing | how many circuits move and how easy their routes are to reach |
| Water heater with isolator | heater rating, location and condition of the existing line |
WhatsApp us a photo of the board or the AC location and we will give you the price before the visit.
Staying safe under summer loads
A simple rule: never run an AC through an extension lead or plug-in adaptor, however heavy-duty it looks. They are made for small appliances, and the steady AC current slowly cooks them until the plastic melts.
Warning: a breaker that trips again straight after you reset it is telling you something; do not reset it a third time or tape it up. If smoke or a burning smell comes from the board, switch off the main breaker, step away, never use water, and call us.
The Saudi Building Code expects proper circuit protection and sound earthing, and earth-leakage protection in bathrooms and kitchens is a core part of that. If your board has no RCD, ask for one on the same visit.
Nearby districts we cover
Our technicians move between Al-Khalidiyah and neighbouring districts such as Al-Fayha, electrician in Al-Faisaliyah and Al-Hindawiyah, and reach the rest of Makkah on request.
Get your home ready for the heat
Call 0565564857 or send a photo of your board, and we will book an Al-Khalidiyah visit to measure loads and AC lines.
Call 0565564857WhatsApp
